TOURATECH ツラーテックZEGA-PRO 「And-black」 パニアシステム 45＋45L BMW F650GS / F650GS Dakar

価格176955円

●メーカー品番：01-052-3159-0●適合車種：BMW G650GS Sertao／F650GS／Dakar●備考：■ブラックアルマイト仕様につきまして■ ブラックアルマイト仕様につきましては、国際輸送時の振動等により表面のブラックアルマイト部分に微細キズが付いてしまう恐れがあります。実用上は全く問題ありませんがこれらの外観上の問題については免責（保証対象外）とさせて頂きますので予めご了承下さい。The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. Pillion comfort not restricted in any way. Enhances the enduro and touring appearance of the BMW F650GS ／ F650GS Dakar.The anodised version of the ZEGA Pro doesn’t just shine in its fabulous black look， but also prevents rubbing inside the case. The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 110 cm- black rackPannier systemRobust steel pannier frame made from 18mm diameter steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Black plastic coated. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy， the case is available in a 45／45 litre version， made entirely of 1.5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！ The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）. You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus， for instance， a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate. The advantages at a glance： - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system：2 aluminium pannier Zega Pro ＊And-black＊ 45 litres， with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2 アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格164212円

●メーカー品番：01-300-6060-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolutionAfter ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， schwarz- sturdy connecting bar- overall width： 107 cmRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 38 litres1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「And-black」 パニアシステム 31＋31L BMW F650GS / F650GS Dakar

価格176955円

●メーカー品番：01-052-3157-0●適合車種：BMW G650GS Sertao／F650GS／Dakar●備考：■ブラックアルマイト仕様につきまして■ ブラックアルマイト仕様につきましては、国際輸送時の振動等により表面のブラックアルマイト部分に微細キズが付いてしまう恐れがあります。実用上は全く問題ありませんがこれらの外観上の問題については免責（保証対象外）とさせて頂きますので予めご了承下さい。The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. Pillion comfort not restricted in any way. Enhances the enduro and touring appearance of the BMW F650GS／ F650GS Dakar.The anodised version of the ZEGA Pro doesn’t just shine in its fabulous black look， but also prevents rubbing inside the case. The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 94 cm- black rackPannier systemRobust steel pannier frame made from 18mm diameter steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Black plastic coated. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy， the case is available in a 31／31 litre version， made entirely of 1.5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！ The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）. You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus， for instance， a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate. The advantages at a glance： - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system：2 aluminium pannier Zega Pro ＊And-black＊ 31 litres， with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「And-black」 パニアシステム 31＋31L BMW F650GS / F650GS Dakar

価格176955円

●メーカー品番：01-052-3157-0●適合車種：BMW G650GS Sertao／F650GS／Dakar●備考：■ブラックアルマイト仕様につきまして■ ブラックアルマイト仕様につきましては、国際輸送時の振動等により表面のブラックアルマイト部分に微細キズが付いてしまう恐れがあります。実用上は全く問題ありませんがこれらの外観上の問題については免責（保証対象外）とさせて頂きますので予めご了承下さい。The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. Pillion comfort not restricted in any way. Enhances the enduro and touring appearance of the BMW F650GS／ F650GS Dakar.The anodised version of the ZEGA Pro doesn’t just shine in its fabulous black look， but also prevents rubbing inside the case. The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 94 cm- black rackPannier systemRobust steel pannier frame made from 18mm diameter steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Black plastic coated. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy， the case is available in a 31／31 litre version， made entirely of 1.5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！ The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）. You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus， for instance， a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate. The advantages at a glance： - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system：2 aluminium pannier Zega Pro ＊And-black＊ 31 litres， with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格159391円

●メーカー品番：01-300-5700-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 94 cm- Stainless steel rack Pannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 31／31 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro 31 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2 アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格162319円

●メーカー品番：01-300-6010-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After Zega and Zega Pro， we have now developed the Zega Pro2． Based on the Zega Pro，its excellent properties have all been retained， but many details have also been significantly improved．The Zega Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！It is factory-fitted with an entirely new attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism．The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the Zega Pro2 can also cope with extreme loads．The supports for the Zega Pro2 accessories holder are also standard fittings on the pre-assembled Zega Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning Zega Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all Zega Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fibreglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．Zega Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Stainless steel rack- sturdy connecting bar- overall width： 107 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit．Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier Zega Pro2 38 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for Zega Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2 アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格162319円

●メーカー品番：01-300-6020-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After Zega and Zega Pro， we have now developed the Zega Pro2． Based on the Zega Pro，its excellent properties have all been retained， but many details have also been significantly improved．The Zega Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！It is factory-fitted with an entirely new attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism．The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the Zega Pro2 can also cope with extreme loads．The supports for the Zega Pro2 accessories holder are also standard fittings on the pre-assembled Zega Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning Zega Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all Zega Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fibreglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．Zega Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Stainless steel rack- sturdy connecting bar- overall width： 115 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit．Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier Zega Pro2 45 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for Zega Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-S」アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格179710円

●メーカー品番：01-300-6071-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolutionAfter ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 115 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-S 45 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2 アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格162319円

●メーカー品番：01-300-6000-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After Zega and Zega Pro， we have now developed the Zega Pro2． Based on the Zega Pro，its excellent properties have all been retained， but many details have also been significantly improved．The Zega Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！It is factory-fitted with an entirely new attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism．The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the Zega Pro2 can also cope with extreme loads．The supports for the Zega Pro2 accessories holder are also standard fittings on the pre-assembled Zega Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning Zega Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all Zega Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fibreglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．Zega Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Stainless steel rack- sturdy connecting bar- overall width： 99 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit．Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier Zega Pro2 31 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for Zega Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格159391円

●メーカー品番：01-300-5720-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 110 cm- stainless steel rack Pannier system Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 45／45 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro 45 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格159391円

●メーカー品番：01-300-5720-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 110 cm- stainless steel rack Pannier system Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 45／45 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro 45 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-S」アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格179710円

●メーカー品番：01-300-6071-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolutionAfter ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 115 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-S 45 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-S」アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格179710円

●メーカー品番：01-300-6061-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolutionAfter ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 107 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-S 38 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-black」アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格185996円

●メーカー品番：01-300-6072-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 115 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-Black 45 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-black」アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格185996円

●メーカー品番：01-300-6052-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 99 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 31 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-black」アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格185996円

●メーカー品番：01-300-6062-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 107 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-Black 38 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-black」アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格185996円

●メーカー品番：01-300-6052-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 99 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 31 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2 アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格162319円

●メーカー品番：01-300-6010-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After Zega and Zega Pro， we have now developed the Zega Pro2． Based on the Zega Pro，its excellent properties have all been retained， but many details have also been significantly improved．The Zega Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！It is factory-fitted with an entirely new attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism．The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the Zega Pro2 can also cope with extreme loads．The supports for the Zega Pro2 accessories holder are also standard fittings on the pre-assembled Zega Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning Zega Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all Zega Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fibreglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．Zega Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Stainless steel rack- sturdy connecting bar- overall width： 107 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit．Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier Zega Pro2 38 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for Zega Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-black」アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格185996円

●メーカー品番：01-300-6062-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 107 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-Black 38 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-S」アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格179710円

●メーカー品番：01-300-6051-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolutionAfter ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 99 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-S 31 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-S」アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格179710円

●メーカー品番：01-300-6051-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolutionAfter ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 99 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-S 31 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-black」アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格185996円

●メーカー品番：01-300-6072-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 115 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-Black 45 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2「And-S」アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar（ブラックフレーム）

価格179710円

●メーカー品番：01-300-6061-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolutionAfter ZEGA and ZEGA Pro， we have now developed the ZEGA Pro2． Based on the ZEGA Pro，its excellent properties have all been retained， but many details have also been significantly improved．The ZEGA Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！ It is factory-fitted with an entirelynew attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism． The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the ZEGA Pro2 can also cope with extreme loads．The supports for the ZEGA Pro2 accessories holder are also standard fittings on the pre-assembled ZEGA Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning ZEGA Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND-blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all ZEGA Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fiBReglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．ZEGA Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Steel rack， black- sturdy connecting bar- overall width： 107 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit． Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier ZEGA Pro2 And-S 38 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for ZEGA Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO「and-S」パニアシステム 38＋38L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格175406円

●メーカー品番：01-300-5711-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．The anodised version of the ZEGA Pro doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 102 cm- Stainless steel rackPannier system Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 38／38 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro ＊And-S＊ 38 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO「and-S」パニアシステム 38＋38L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格175406円

●メーカー品番：01-300-5711-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．The anodised version of the ZEGA Pro doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 102 cm- Stainless steel rackPannier system Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 38／38 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro ＊And-S＊ 38 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2 アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格162319円

●メーカー品番：01-300-6000-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After Zega and Zega Pro， we have now developed the Zega Pro2． Based on the Zega Pro，its excellent properties have all been retained， but many details have also been significantly improved．The Zega Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！It is factory-fitted with an entirely new attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism．The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the Zega Pro2 can also cope with extreme loads．The supports for the Zega Pro2 accessories holder are also standard fittings on the pre-assembled Zega Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning Zega Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all Zega Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fibreglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．Zega Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Stainless steel rack- sturdy connecting bar- overall width： 99 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit．Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier Zega Pro2 31 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for Zega Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格159391円

●メーカー品番：01-300-5710-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 102 cm- stainless steel rack Pannier system Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 38／38 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge；also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro 38 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO アルミニウムパニアシステム 38＋38L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格159391円

●メーカー品番：01-300-5710-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 102 cm- stainless steel rack Pannier system Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 38／38 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge；also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro 38 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO2 アルミニウムパニアシステム 45＋45L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格162319円

●メーカー品番：01-300-6020-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The next step in evolution After Zega and Zega Pro， we have now developed the Zega Pro2． Based on the Zega Pro，its excellent properties have all been retained， but many details have also been significantly improved．The Zega Pro2 shines with its improved profile for even better operation， a carrying handle as standard and optimised ventilation．Above all， though， the pre-assembled version is an absolute revolution！It is factory-fitted with an entirely new attachment system that combines suitability with maximum ease of use，facilitating single-handed use - you could say it’s Plug and play for fully packed aluminium panniers！There’s a single lever on the outside to operate the mechanism．The lid can stay closed when it is removed from the bike． Pannier on， click - and go！The innovative construction in resilient stainless steel releases the catch before attachment， which means the Zega Pro2 can also cope with extreme loads．The supports for the Zega Pro2 accessories holder are also standard fittings on the pre-assembled Zega Pro2 on both sides of each pannier．They are automatically locked when the lid is closed．Panniers：- improved seal profile for precise and even easier use- carrying handle made of strong harness material as standard， lowered into the handle groove on the pannier lid so no irritation either when sitting or when securing luggage- optimised ventilation system for easy opening at high pressure differences， e．g． after going through a tunnel- including all the benefits of the award-winning Zega Pro aluminium pannier- also available in a lockable version so it can be secured with other Touratech locks Available in 3 sizes （31， 38， 45 litres） and 3 finishes （natural aluminium， anodised silver AND-S and anodised black AND blackThe anodised version of the ZEGA Pro2 doesn’t just shine in its fabulous natural aluminium look， but also prevents rubbing inside the case．The ultra thick， high quality anodised layer offers very special protection for the surface and helps to prevent discoloration．Mounting：- Genuine single-handed use thanks to the pre-assembled mounting system that is fully operated from the outside- conveniently positioned release catches， in a protected position between the pannier and seat- including pre-assembled supports for all Zega Pro2 accessory holders on both sides of a pannier．The very strong construction in stainless steel and fibreglass-reinforced plastic elements provides absolute stability and reliability even under the toughest conditions．The new fixation system further reinforces the overall pannier system．Zega Pro2 panniers will fit on almost any Touratech pannier racks． Their special construction offers the option for balancing out any tolerances．Pannier frame- Stainless steel rack- sturdy connecting bar- overall width： 115 cm Robust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall． Bolted crosspiece for better rigidity． Mounting easy to fit．Uses standard mounting points． No modifications to rear footrests． Mounting bolts are included．Delivery schedule of the system：2 x aluminium pannier Zega Pro2 45 litres 1 x pannier rack including mounting hardware 1 x Integral locks set for Zega Pro2 release catches with 2 simultaneous locking （01-050-3300-0）●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO アルミニウムパニアシステム 31＋31L BMW F650GS/F650GS Dakar/G650GS/G650GS Sertao（シルバーフレーム）

価格159391円

●メーカー品番：01-300-5700-0●適合車種：BMW・G650GS Sertao／F650GS／Dakar●備考：The aluminium pannier system again has a very robust construction．We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle．Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands．The rack is made of 18 mm steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces．Pillion comfort not restricted in any way．Enhances the enduro and touring appearance of the BMWG650GS／Sertao／F650GS／Dakar．- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width： 94 cm- Stainless steel rack Pannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall．Bolted crosspiece for better rigidity．Mounting easy to fit．Uses standard mounting points．No modifications to rear footrests．Mounting bolts are included．Zega Pro In a modern design and state-of-the-art construction， our developers have come up with a veritable masterpiece in the ZEGA Pro．Light and yet sturdy， the case is available in a 31／31 litre version， made entirely of 1．5-mm aluminium， water- and dust-proof， and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium！The lid and base of the ZEGA Pro are welded， which achieves the maximum rigidity of the connections， and the base and outer shell have high quality rivets （no cheap studs for us - or you！）．You’ll find no leaky welded seams along the edges．High quality silicone seals ensure that the contents of this case are protected as well as possible．The highly robust protective strip along the car case is screwed on， and so is easily replaced when necessary - perhaps after a fall．The same applies to the strong protective corners on the lid， which comes off completely or can be opened just from one side - the catches double as hinges．The ZEGA Pro appeals not only for its technology and workmanship， but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye．Thus， for instance， a clever handle can be added to the lid．The four attachment eyes rise only slightly above the surface of the case， so it also makes an ideal seat．Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories．The clever touches of the ZEGA Pro include the ingenious lock system， which is strong and reliable yet easy to operate．The advantages at a glance：- automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge； also available with simultaneous locking with navigation brackets and oil plugs．Delivery schedule of the system：2 aluminium pannier Zega Pro 31 litres 1 pannier rack including mounting hardware Delivery schedule does not include the Rapid-Trap●ご注意：※カギなどのオプションパーツは別売りです。●写真注意：※画像はイメージです。●納期：※メーカー取寄せ商品のため納期にお時間頂きます。なお、完売の際はご了承下さい。【smtb-F】

詳細を確認する

ページ：TOP / 1 /2 /3 /4 /5 /6 /