TOURATECH ツラーテックZEGA-PRO 「And-black」 アルミニウムパニアシステム 31+38L Triumph Tiger 800 XC

価格187546円

●メーカー品番:01-420-5732-0●適合車種:Triumph Tiger 800●備考:■ブラックアルマイト仕様につきまして■ ブラックアルマイト仕様につきましては、国際輸送時の振動等により表面のブラックアルマイト部分に微細キズが付いてしまう恐れがあります。実用上は全く問題ありませんがこれらの外観上の問題については免責(保証対象外)とさせて頂きますので予めご了承下さい。The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous black look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 99 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 31/38 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Aluminium pannier system, premounted.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-black* 31 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro *And-black* 38 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「And-black」 アルミニウムパニアシステム 38+45L Triumph Tiger 800 XC

価格187546円

●メーカー品番:01-420-5737-0●適合車種:Triumph Tiger 800●備考:■ブラックアルマイト仕様につきまして■ ブラックアルマイト仕様につきましては、国際輸送時の振動等により表面のブラックアルマイト部分に微細キズが付いてしまう恐れがあります。実用上は全く問題ありませんがこれらの外観上の問題については免責(保証対象外)とさせて頂きますので予めご了承下さい。The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous black look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 107 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 38/45 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-black* 38 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro *And-black* 45 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「And-black」 アルミニウムパニアシステム 38+45L Triumph Tiger 800 XC

価格187546円

●メーカー品番:01-420-5737-0●適合車種:Triumph Tiger 800●備考:■ブラックアルマイト仕様につきまして■ ブラックアルマイト仕様につきましては、国際輸送時の振動等により表面のブラックアルマイト部分に微細キズが付いてしまう恐れがあります。実用上は全く問題ありませんがこれらの外観上の問題については免責(保証対象外)とさせて頂きますので予めご了承下さい。The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous black look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 107 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 38/45 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-black* 38 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro *And-black* 45 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「And-black」 アルミニウムパニアシステム 31+38L Triumph Tiger 800 XC

価格187546円

●メーカー品番:01-420-5732-0●適合車種:Triumph Tiger 800●備考:■ブラックアルマイト仕様につきまして■ ブラックアルマイト仕様につきましては、国際輸送時の振動等により表面のブラックアルマイト部分に微細キズが付いてしまう恐れがあります。実用上は全く問題ありませんがこれらの外観上の問題については免責(保証対象外)とさせて頂きますので予めご了承下さい。The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous black look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 99 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 31/38 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Aluminium pannier system, premounted.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-black* 31 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro *And-black* 38 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「and-S」 アルミニウムパニアシステム 38+38L Triumph Tiger 800 XC

価格181089円

●メーカー品番:01-420-5731-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous natural aluminium look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- overall width: 99 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 31/38 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-S* 31 litres, with pre-fitted 18 mm fixing kit1 aluminium pannier Zega Pro *And-S* 38 litres, with pre-fitted 18 mm fixing kit1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PROアルミニウムパニアシステム 38+45L Triumph Tiger 800 XC

価格165161円

●メーカー品番:01-420-5735-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 107 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 38/45 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro 38 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro 45 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PROアルミニウムパニアシステム 38+45L Triumph Tiger 800 XC

価格165161円

●メーカー品番:01-420-5735-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 107 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 38/45 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro 38 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro 45 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「and-S」 アルミニウムパニアシステム 38+38L Triumph Tiger 800 XC

価格181089円

●メーカー品番:01-420-5731-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous natural aluminium look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- overall width: 99 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 31/38 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-S* 31 litres, with pre-fitted 18 mm fixing kit1 aluminium pannier Zega Pro *And-S* 38 litres, with pre-fitted 18 mm fixing kit1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「and-S」 アルミニウムパニアシステム 38+45L Triumph Tiger 800 XC

価格181089円

●メーカー品番:01-420-5736-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous natural aluminium look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 107 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 38/45 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-S* 38 litres, with pre-fitted 18 mm fixing kit1 aluminium pannier Zega Pro *And-S* 45 litres, with pre-fitted 18 mm fixing kit1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PRO 「and-S」 アルミニウムパニアシステム 38+45L Triumph Tiger 800 XC

価格181089円

●メーカー品番:01-420-5736-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces. The anodised version of the ZEGA Pro doesn’t just shine in its fabulous natural aluminium look, but also prevents rubbing inside the case. The ultra thick, high quality anodised layer offers very special protection for the surface and helps to prevent discoloration.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 107 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 38/45 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro *And-S* 38 litres, with pre-fitted 18 mm fixing kit1 aluminium pannier Zega Pro *And-S* 45 litres, with pre-fitted 18 mm fixing kit1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PROアルミニウムパニアシステム 31+38L Triumph Tiger 800 XC

価格165161円

●メーカー品番:01-420-5730-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 99 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 31/38 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro 31 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro 38 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TOURATECH ツラーテックZEGA-PROアルミニウムパニアシステム 31+38L Triumph Tiger 800 XC

価格165161円

●メーカー品番:01-420-5730-0●適合車種:Triumph Tiger 800●備考:The aluminium pannier system again has a very robust construction. We have tried to bring the pannier racks and the panniers as close as possible to the motorcycle. Numerous tests have already been performed in order to ensure that the entire development satisfies the required demands. The rack is made of 18 mm stainless steel tubing and is attached to existing mounting points using special fixing clips and reinforcing pieces.- ready fitted fixing kits- sturdy connecting bar- original indicators can be re-used- overall width: 99 cm- Stainless steel rackPannier systemRobust steel pannier frame made from 18mm diameter stainless steel tube with a 2mm thick wall. Bolted crosspiece for better rigidity. Mounting easy to fit. Uses standard mounting points. No modifications to rear footrests. Mounting bolts are included.Zega Pro In a modern design and state-of-the-art construction, our developers have come up with a veritable masterpiece in the ZEGA Pro.Light and yet sturdy, the case is available in a 31/38 litre version, made entirely of 1.5-mm aluminium, water- and dust-proof, and manufactured to the highest standards - no way were we going to settle for a basic plastic construction that was simply jazzed up with a few bits of moulded aluminium! The lid and base of the ZEGA Pro are welded, which achieves the maximum rigidity of the connections, and the base and outer shell have high quality rivets (no cheap studs for us - or you!). You’ll find no leaky welded seams along the edges. High quality silicone seals ensure that the contents of this case are protected as well as possible.The highly robust protective strip along the car case is screwed on, and so is easily replaced when necessary - perhaps after a fall. The same applies to the strong protective corners on the lid, which comes off completely or can be opened just from one side - the catches double as hinges. The ZEGA Pro appeals not only for its technology and workmanship, but also for the many clever detail solutions and the modern protected design - the rounded lines of the item really do catch the eye. Thus, for instance, a clever handle can be added to the lid. The four attachment eyes rise only slightly above the surface of the case, so it also makes an ideal seat. Some of the other benefits of the ZEGA Pro are that it is easy to open to retrieve a luggage roll and our extensive range of accessories. The clever touches of the ZEGA Pro include the ingenious lock system, which is strong and reliable yet easy to operate. The advantages at a glance: - automatic locking prevents the catches from opening accidentally- fitted locks can be replaced or added later without drilling or filing- simultaneously locking fitted locks are available at no extra charge; also available with simultaneous locking with navigation brackets and oil plugs.Delivery schedule of the system:1 aluminium pannier Zega Pro 31 litres, with pre-fitted 18 mm fixing kit 1 aluminium pannier Zega Pro 38 litres, with pre-fitted 18 mm fixing kit 1 pannier rack including mounting hardware※カギなどのオプションパーツは別売りです。●写真注意:※画像はイメージです。●納期:メーカー取寄せ商品のため完売の際は納期にお時間頂きます。また、販売終了の場合もございますので予めご了承下さい。【smtb-F】

詳細を確認する

TRIUMPH Tiger800/XC(11〜14年) OBK37/48専用CAMパニアホルダー(サイドケースホルダー)PL6401CAM GIVI(ジビ)

価格29160円

【適合車種】TRIUMPH Tiger800/XC【適合年式】11〜14年※商品画像は79662+79692の装着例の商品画像となります。実際の商品はパニアホルダーのみとなりますのでご注意下さい。ボックスは別途お買い求めが必要です。key:サイドケースホルダーzero768861※商品画像は79662+79692の装着例の商品画像となります。実際の商品はパニアホルダーのみとなりますのでご注意下さい。ボックスは別途お買い求めが必要です。GIVI製TREKKER OBK37/48専用CAMパニアホルダー(サイドケースホルダー)【商品名】OBK37/48専用CAMパニアホルダー(サイドケースホルダー)PL6401CAM【商品番号】G3-79692【メーカー】GIVI(ジビ)【車種メーカー】TRIUMPH(トライアンフ)【適合車種】TRIUMPH Tiger800/XC【適合年式】11〜14年

詳細を確認する

ページ:TOP / 1 /